Scion xD Key Fob Programming by Year

Can you program a xD fob without the dealer? For most years, yes. Pick your year for the route and best next step.

Find your year

YearDIY onboard?How it programsWorking fob?Erase riskConfidenceBest next step
2008–2012YesYes - onboard relearnMedFollow the steps below

Scion xD key types & programming facts

2008-2012 Scion xD models equipped with anti-theft use a remote‑head key that combines the mechanical blade, transponder chip, and keyless entry buttons in one unit. Programming typically has two parts: cutting the mechanical blade and electronically programming both the immobilizer transponder and the remote‑locking functions to the vehicle using approved procedures or equipment. Many suppliers note that these keys must be programmed by a dealership or qualified automotive locksmith rather than being universally self‑programmable.

Key types used on the xD:

  • remote-head key (integrated key + remote with transponder chip) (2008-2012 USA/Canada Scion xD with anti-theft, per parts listings and compatibility notes for 2008-2012 xD remote-head key fobs)

Common fob FCC IDs: MOZB41TG — check the back of your fob; we confirm the exact variant on site.

2008–2012 Scion xD

Route verified — exact steps vary by trim/equipment

Route verified as onboard programming (no dealer needed). The sequences below are general route guidance — use them only if your vehicle shows the same prompts and controls. If the prompts don’t match, stop and call us.

Show the programming methods (19 steps)

Preparation

Remove the key
1 Remove key from ignition before starting procedure
Programming step
2 Open and unlock driver-side door as initial step
Close the doors
3 Close all other doors including trunk prior to programming
Programming step
4 Have all remotes to be programmed ready before entering programming mode
Wait / timing window
5 Ensure actions performed within specified timing (e.g., within 5 seconds for step 3)

Entering Programming Mode

Insert the key
1 Within 5 seconds insert key into ignition and pull out twice
Close the doors
2 Close then open driver-side door twice, repeated as required by steps 4 and 6
Insert the key
3 Insert key into ignition and leave it in during later steps (step 7)
Close the doors
4 Close driver-side door before switching ignition per step 8
Remove the key
5 Switch ignition to ON then OFF, then remove key to trigger lock-cycle confirmation

Programming Remotes

Cycle the ignition ON/OFF
1 After programming mode entry, door locks cycle to confirm programming mode active
Press LOCK + UNLOCK
2 Push and hold LOCK and UNLOCK buttons for 1.5 seconds on each remote being programmed
Press / hold a fob button
3 Immediately after releasing, push and hold LOCK button for 2 seconds to complete remote programming
Cycle the ignition ON/OFF
4 Door locks will cycle to confirm successful programming of each remote
Programming step
5 Repeat the push/hold sequence for additional remotes as needed

Completion and Troubleshooting

Programming step
1 Open driver-side door to exit programming; programming completes at this point
Cycle the ignition ON/OFF
2 Verify door lock cycles occurred to confirm successful entry into programming and remote registration
Programming step
3 Replace key fob battery if fob not working before reprogramming attempts
Programming step
4 Links referenced for battery replacement, fob replacement, and site policies (Home, Disclaimer, YouTube, Privacy Policy)

How we validate this guide

Year coverage comes from our consolidated vehicle programming dataset. Route-level programming status is reviewed against internal route sheets and available manufacturer, security-access, and professional tool references. Exact button sequences are marked source-verified only when we have year/equipment-specific support; where a year is labeled “route verified, steps vary,” we confirm the exact fob, trim, and prompts before programming. Reviewed for route and safety by Mohammad H. Abdelhadi, ALOA-Certified Master Locksmith.

YearRoute statusExact steps
2008–2012Route verifiedGeneral guidance

Common questions

What type of key does my 2008-2012 Scion xD use?

Most 2008-2012 Scion xD models with anti-theft use a 3‑button remote-head key that includes a transponder chip and keyless entry functions.

Can I program a new Scion xD remote key myself?

Some basic procedures may be done onboard, but many suppliers state the remote-head key for 2008-2012 xD generally requires programming by a dealer or automotive locksmith.

Is there a specific FCC ID for the Scion xD remote key?

Yes. Many 2008-2012 Scion xD remote-head keys list compatible FCC ID **MOZB41TG** for the integrated remote and transponder key.

Can you program a xD key fob without going to the dealership?

For most years, yes - the route is onboard relearn or an OBD tool, both of which a mobile locksmith handles at your location.

Does this program the remote only, or the transponder key too?

It depends on your key type. Tell us your FCC ID and we will confirm.

What if my year says professional programming required?

Those years need a programmer or security access; we bring the tool to you and program it on site.

How much does it cost?

It depends on year, key type, and whether you have a working key. Call (833) 439-8636 for a firm price before we dispatch.

Need your xD fob programmed? We come to you, 24/7.
Scroll to Top
☎  Tap to call 24/7 — (833) 439-8636