Here at Low Rate Automotive Locksmith we are your source for free instructions on how to program your Infiniti keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Infiniti Locksmith offers detailed step-by-step directions from the manufacturer of your Infiniti car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.

Here is the list of Infiniti G20 Years and models this supports:

 

  • 1991 Infiniti G20
  • 1992 Infiniti G20
  • 1993 Infiniti G20
  • 1994 Infiniti G20
  • 1995 Infiniti G20
  • 1996 Infiniti G20

 

  • 1997 Infiniti G20
  • 1998 Infiniti G20
  • 1999 Infiniti G20
  • 2000 Infiniti G20
  • 2001 Infiniti G20
  • 2002 Infiniti G20

1991-1993 Infiniti G20 Car Fob and Remote Programming Instructions:

(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver’s door once to enable “Belting” mode.
(5) Push lock button on the new remote controller once, within 5 seconds of
completing step 4.
(6) If additional remotes are needed, repeat steps 4 and 5 for each additional
remote immediately after programming the first remote.

NOTE: a total of four (4) remotes can be programmed to function on the
same vehicle.

1993-1996 Infiniti G20 Car Fob and Remote Programming Instructions:

These instructions are for G20 1993.5 models and will not work on early 1993 models

1993.5 – 1996 G20 (No automatic seatbelts)
(Only models with Leather seats and Sunroof)

1991-1996 G20 Touring (ALL)

(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver’s door once to enable “Belting” mode.
(5) Push lock button on the new remote controller once, within 5 seconds of
completing step 4.
(6) If additional remotes are needed, repeat steps 4 and 5 for each additional
remote immediately after programming the first remote.

NOTE: a total of four (4) remotes can be programmed to function on the
same vehicle.

1999-2002 Infiniti G20 Car Fob and Remote Programming Instructions:

1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.

5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

 

If you have any questions or need a professional Locksmith To assist you with your Infiniti G20 Key Fab Programming, below is a list of Low Rate Locksmith Locations.

The Infiniti G20 was Infiniti’s entry-level luxury car in the United States during most of the 1990s and into the 2000s. Similar to the Japanese/European market Nissan Primera sedan, itself a luxury package of the Nissan Pulsar, the G20 offered higher levels of standard equipment. It was launched in 1990 as Infiniti’s first small car as an entry-level alternative to the Q45; later advertisements emphasized its European heritage with the tag line “Born in Japan. Educated in Europe. Now Available in America.”

The G20 was temporarily discontinued after the 1996 model year, leaving the I30 as Infiniti’s lowest-priced car for the 1997 & 1998 model years. The first second-generation 1999 G20 was completed on May 18, 1998. The final second-generation 2002 G20 was completed on January 11, 2002.